Amaranth Fire Vienna Ceramic Wall Decos 4x8
STOCK:2-4 weeks lead time
- If you have a Country Floors trade account you are eligible for online account access.
Please register here for your online access.
- Quantities available is subject to material in transfer, transit and prior sale. Please call your branch to confirm availability.
- Please call for shipment dates on incoming stock.
|Usage||Comm. Interior Walls, Res. Interior Walls, Shower Walls|
|Collection||Status Special Order Ceramic||Color||Green|
|Frost Resistance||-||Area||Bathroom, Kitchen, Living Room|
Ceramic tile is a fired clay product. They may be glazed or unglazed, depending on the desired design concept and particular usage. Glazed ceramic tiles and many unglazed ceramic tiles are generally moisture resistant and therefore are suited for floor and wall spaces such as general living areas, bathrooms, kitchens, and so forth. Ceramic tile is relatively easy to keep clean, as they can tolerate many different common household cleaning products. Typically, ceramic tile does not absorb fumes, odors, or smoke. Because color may be fired into a tile’s clay body (in the case of unglazed tiles) or onto a tile’s glazed surface (for glazed tiles), ceramic tile will not usually lose color or fade when exposed to UV rays in sunlit conditions. Although many tiles have little to no variation, color can vary from tile to tile to differing degrees. This is an inherent and desired characteristic of all fired clay products. Therefore, all tile should be unpacked and inspected prior to installation, as Country Floors cannot accept claims for variation in any tile after installation.
- Unglazed ceramic tile is typically more porous and will potentially absorb liquids and stains. It needs to be sealed to protect the surface from liquids. Staining can be prevented to some extent by sealing with a quality chemical ceramic tile sealer and will need to be sealed periodically in order to continue to be free from stains.
- The grout placed in between ceramic tiles is susceptible to moisture, so it will need to be sealed to make it impervious to water. Otherwise, water can seep through the grout, which weakens the installation and encourages mold growth.
- Unglazed ceramic tiles have greater slip resistance than glazed tiles. Because they can be slippery, glossy tiles are not generally recommended for high traffic areas or for residential sites with children and elderly people.
- Ceramic tile is durable but may be subject to chipping in environments with aggressive use.
- Check the technical specifications assigned a particular tile product.
Get the most out of your Country Floors product by following these helpful instructions for installing floor tile. A Few Dos & Don’ts
- Tile may be installed over most structurally sound substrates if they are clean, smooth, dry and free of wax, soap scum and grease and other debris.
- Carefully read and follow all instructions and precautions on the adhesive or mortar package. Mix only enough to be used within 30 minutes.
- Since variation of shades is an inherent characteristic of ceramic tile, mix tiles from several cartons as you set, for a blended effect.
- Order extra material for cuts, spare tiles, and waste.
- If material is face taped, remove tape after installation.
- Be sure to calculate exact tile needed for your surface before installation.
- If you are short of material do not start installation until you have all the tile that blends. Additional shipments may not match the tile from previous shipment.
- If you do order additional tile for an older job be sure to match color lots before installation.
Tile may be installed over most structurally sound substrates, if they are clean, smooth, dry and free of wax, soap scum and grease. Any damaged, loose or uneven areas must be repaired, patched and leveled. Remove any moldings, trim, appliances, etc., which could interfere with installation. Door jambs may be undercut for tile to slip under. We recommend waterproofing most floors to prevent surface seeping.
Begin by marking the center point of all four walls. Snap chalk lines between the center points of opposite walls, which will intersect at the center of room. Make sure they›re perfectly square, and adjust if necessary. Next, lay out a row of loose tiles along the center lines in both directions, leaving spaces for uniform joints (use tile spacers). If this layout leaves cuts smaller than 1/2 tile at walls, adjust the center line by snapping a new line 1/2 tile closer to the wall. Repeat along other center line if necessary. Now divide the room into smaller grids (approx. 2' x 3') by snapping additional lines parallel to center lines.
Select the right adhesive for the substrate you're using. Carefully read and follow all instructions and precautions on the adhesive or mortar package. Mix only enough to be used within 30 minutes. Using the type of trowel recommended on the adhesive package spread a 1/4" coat on the surface of one grid area, using the flat side of the trowel. Do not cover guidelines. Next, use the notched side of trowel to comb adhesive into standing ridges by holding trowel at a 45-degree angle. Then remove excess adhesive, leaving a uniform, ridged setting bed. Don't spread a larger area than can be set in 15 minutes.
We recommend using white good quality thin set such as Mapei, Laticrete, or Ardex.
Some black marbles, white marbles, dolomites, and green marbles may have to be installed with Moisture sensitive thin set. Please check with the manufacturer.
Carefully measure tiles to be cut and mark with a pencil or felt-tip pen. Make straight or diagonal cuts with a tile cutter, curved cuts with a nipper (chipping away small pieces for best results) and full-length curved cuts with a rod saw. Sharp-cut edges may be smoothed with a carborundum stone.
Variation of shades is an inherent characteristic of marble, stone and ceramic tile – mix tiles from several cartons as you set, for a blended effect. Begin installing tiles in the center of the room, one grid at a time. Finish each grid before moving to the next. Start with the first tile in the corner of the grid and work outward. Set tiles one at a time using a slight twisting motion. Don't slide tiles into place. Insert tile spacers as each tile is set, or leave equal joints between tiles. Fit perimeter tiles in each grid last, leaving 1/4" gap between tile and wall. Any rectangle porcelain should never be set in a running bond pattern, rather no more than a 1/3 overlap; the joint should be widened to 3/16" and use of a large unit porcelain mortar should be employed. When grid is completely installed, tap in all tiles with a rubber mallet or hammer and wood block to ensure a good bond and level plane. Remove excess adhesive from joints with a putty knife and from tile with a damp sponge. Do not walk on tiles until they are set (usually in 24 hours).
Generally, you should wait about 24 hours before grouting (refer to the adhesive package for specifics). Carefully read and follow all instructions and precautions on the grout package. Make only enough to use in about 30 minutes. Remove tile spacers and spread grout on the tile surface, forcing down into joints with a rubber grout float or squeegee. Tilt the float at a 45-degree angle. Remove excess grout from surface immediately with the edge of float. Tilt it at a 90-degree angle and scrape it diagonally across tiles. Wait 15-20 minutes for grout to set slightly, then use a damp sponge to clean grout residue from surface and smooth the grout joints. Rinse sponge frequently and change water as needed. Let dry until grout is hard and haze forms on tile surface, then polish with a soft cloth. Rinse again with sponge and clean water if necessary. Wait 72 hours for heavy use. Don't apply sealers or polishes for three weeks, and then only in accordance with manufacturer's recommendations.
For travertine tiles, materials with holes, aqua forte etc. use a grout release before grouting. You can also a sealer before grouting. This will help you clean the grout easier.