Renovating your home is easier than ever with Matrix Azul Matte Porcelain Tile. From bathrooms to kitchens, you can make any location look perfect. Porcelain tile is a type of clay product that can be used for many purposes. You'll find it in kitchens, bathrooms, and hotels throughout the world. Porcelain tiles are impervious to everyday residential use such as kitchen floors or bathroom walls which makes them perfect for wet areas like showers! Porcelain is a type of material that, unlike ordinary ceramics, has much more durability for everyday floor and wall tiles. For this product to be classified as Porcelain it needs less than 1% water absorption rate and some other technical specifications as specified by the Tile Council of America. This wall tile with a modern matte finish is sure to lend sophisticated splendor where it's needed. The Gray Porcelain is an elegant choice for any space. It will accentuate the beauty of your tiles while adding character to your design scheme..
For a modern and stylish look, there are many options from floor to wall tiles with matching mosaics that give your home the perfect finishing touch. The size of this product 12x24x25/64. You can use the site search to find a different size of this product - we've got it all!
Porcelain tile can be termed a type or subset of ceramic tile. However, to be truly considered as porcelain tile, there are other, more stringent standards that must be met to differentiate it from mere ceramic tile. The essence of this increased burden centers around strength and moisture resistance. Typically, porcelain tile was composed of kaolin clay, feldspar, and quartz. To a degree, this remains the essence of the material. It is also fired at significantly higher temperatures than traditional ceramic tile might be. This results in the strength and water absorption advantages that porcelain tile is so well known for. This strength and moisture resistance creates a scenario where porcelain tile becomes the finish of choice for both heavy-duty commercial applications and lovingly conceived residential design plans. Naturally, this resistance to foot traffic and staining makes for a product with a serious sense of permanence. As a fired clay product, variation in shade and color can occur from tile to tile. This is an inherent and desired characteristic. Therefore, all tile should be unpacked and inspected prior to installation, as Country Floors cannot accept claims for variation in any porcelain tile after installation. Please check technical specifications for more detail on a particular product.
Get the most out of your Country Floors product by following these helpful instructions for installing floor tile. A Few Dos & Don’ts
Tile may be installed over most structurally sound substrates, if they are clean, smooth, dry and free of wax, soap scum and grease. Any damaged, loose or uneven areas must be repaired, patched and leveled. Remove any moldings, trim, appliances, etc., which could interfere with installation. Door jambs may be undercut for tile to slip under. We recommend waterproofing most floors to prevent surface seeping.
Begin by marking the center point of all four walls. Snap chalk lines between the center points of opposite walls, which will intersect at the center of room. Make sure they›re perfectly square, and adjust if necessary. Next, lay out a row of loose tiles along the center lines in both directions, leaving spaces for uniform joints (use tile spacers). If this layout leaves cuts smaller than 1/2 tile at walls, adjust the center line by snapping a new line 1/2 tile closer to the wall. Repeat along other center line if necessary. Now divide the room into smaller grids (approx. 2' x 3') by snapping additional lines parallel to center lines.
Select the right adhesive for the substrate you're using. Carefully read and follow all instructions and precautions on the adhesive or mortar package. Mix only enough to be used within 30 minutes. Using the type of trowel recommended on the adhesive package spread a 1/4" coat on the surface of one grid area, using the flat side of the trowel. Do not cover guidelines. Next, use the notched side of trowel to comb adhesive into standing ridges by holding trowel at a 45-degree angle. Then remove excess adhesive, leaving a uniform, ridged setting bed. Don't spread a larger area than can be set in 15 minutes.
We recommend using white good quality thin set such as Mapei, Laticrete, or Ardex.
Some black marbles, white marbles, dolomites, and green marbles may have to be installed with Moisture sensitive thin set. Please check with the manufacturer.
Carefully measure tiles to be cut and mark with a pencil or felt-tip pen. Make straight or diagonal cuts with a tile cutter, curved cuts with a nipper (chipping away small pieces for best results) and full-length curved cuts with a rod saw. Sharp-cut edges may be smoothed with a carborundum stone.
Variation of shades is an inherent characteristic of marble, stone and ceramic tile – mix tiles from several cartons as you set, for a blended effect. Begin installing tiles in the center of the room, one grid at a time. Finish each grid before moving to the next. Start with the first tile in the corner of the grid and work outward. Set tiles one at a time using a slight twisting motion. Don't slide tiles into place. Insert tile spacers as each tile is set, or leave equal joints between tiles. Fit perimeter tiles in each grid last, leaving 1/4" gap between tile and wall. Any rectangle porcelain should never be set in a running bond pattern, rather no more than a 1/3 overlap; the joint should be widened to 3/16" and use of a large unit porcelain mortar should be employed. When grid is completely installed, tap in all tiles with a rubber mallet or hammer and wood block to ensure a good bond and level plane. Remove excess adhesive from joints with a putty knife and from tile with a damp sponge. Do not walk on tiles until they are set (usually in 24 hours).
Generally, you should wait about 24 hours before grouting (refer to the adhesive package for specifics). Carefully read and follow all instructions and precautions on the grout package. Make only enough to use in about 30 minutes. Remove tile spacers and spread grout on the tile surface, forcing down into joints with a rubber grout float or squeegee. Tilt the float at a 45-degree angle. Remove excess grout from surface immediately with the edge of float. Tilt it at a 90-degree angle and scrape it diagonally across tiles. Wait 15-20 minutes for grout to set slightly, then use a damp sponge to clean grout residue from surface and smooth the grout joints. Rinse sponge frequently and change water as needed. Let dry until grout is hard and haze forms on tile surface, then polish with a soft cloth. Rinse again with sponge and clean water if necessary. Wait 72 hours for heavy use. Don't apply sealers or polishes for three weeks, and then only in accordance with manufacturer's recommendations.
For travertine tiles, materials with holes, aqua forte etc. use a grout release before grouting. You can also a sealer before grouting. This will help you clean the grout easier.